New way for players to play Eshop with code.bin on their New 3DS and Old 3DS (9.0-9.2). It makes you can go to the Eshop without the newest Firmware.
CURRENTLY IT IS ONLY AVIALABLE BETWEEN 9.0 AND 9.2 (lower firmwares may be supported one day, but, without a new kernel exploit, there is no chances for 9.3+)
NEW 3DS METHOD
NEW 3DS METHOD
Download this and place the contents of the '3DS Stuff' folder on the root directory of your SD card save for rxTools.dat and firmware.bin. Those will come later, so save them.
Its’s very simple.
Launch NTR CFW on a New 3DS.
Enable the debugger.
Connect the debugger with the command : connect(‘your3dsip’, 8000)
And now the magic command UPDATED (may not work on 8.1J) : write(0x10DD28, (0x00, 0x20, 0x08, 0x60, 0x70, 0x47), pid=0x25)
Done !
Launch NTR CFW on a New 3DS.
Enable the debugger.
Connect the debugger with the command : connect(‘your3dsip’, 8000)
And now the magic command UPDATED (may not work on 8.1J) : write(0x10DD28, (0x00, 0x20, 0x08, 0x60, 0x70, 0x47), pid=0x25)
Done !
OLD 3DS METHOD
Download the code.bin
http://gbatemp.net/attachments/code-rar.18403/
Copy it to the root of your SD card
Launch the web browser
Clear cookies and history
Go to loadcode.projectpokemon.org
Wait for the load bar and the message “failed to load” to disappear
Press Home
Done !
http://gbatemp.net/attachments/code-rar.18403/
Copy it to the root of your SD card
Launch the web browser
Clear cookies and history
Go to loadcode.projectpokemon.org
Wait for the load bar and the message “failed to load” to disappear
Press Home
Done !
LIMITATIONS :
It’s now stable.
Set your internet connection BEFORE and make sure it’s valid.
Access the service you want after you see “finish” in the debugger.
Tested with :
-eShop
-eShop in games (update of Mii Plaza, DLCs, etc.)
-System Transfer (but the source and the target need to have a firmware in the compatiblity list) —> a whole system transfer has been tested and it work!
-Theme Shop
Set your internet connection BEFORE and make sure it’s valid.
Access the service you want after you see “finish” in the debugger.
Tested with :
-eShop
-eShop in games (update of Mii Plaza, DLCs, etc.)
-System Transfer (but the source and the target need to have a firmware in the compatiblity list) —> a whole system transfer has been tested and it work!
-Theme Shop
TROUBLESHOOTING :
Question : The browser method doesn’t work. What can I do?
Answer : Install the right version of the browser (see below).
Answer : Install the right version of the browser (see below).
Question : When I select my target 3DS in the System Transfer, it fails! What can I do?
Answer : Install the right version of CARDBROAD on BOTH 3DS (see below).
Answer : Install the right version of CARDBROAD on BOTH 3DS (see below).
Advertisements
- 1. Backup Nintendo 3DS folder to PC
- 2. Download latest Gateway release at http://www.gateway-3ds.com/downloads/
- 4. Copy slot0x25KeyX.bin to sd:/root
- 6. Go to http://go.gateway-3ds.com
- 8. Copy nand.bin to PC
- 10. Copy Nintendo 3DS folder and files back to the SD card
- II. rxTools installation
- 2. Download firmware.bin using /tools/cdn_firm.py
- 4. Delete rxTools.dat, firmware.bin and rxTools directory from SD card(if it exists)
- 5. Copy slot0x25KeyX.bin into sd:/root
- 6. Go to http://dukesrg.github.io/?rxTools/sys/code.bin
- 7. Wait until installation finishes and then boot to rxTools emunand once
- III. Unlink nands
- 1. In sysnand, go to System Settings -> Other Settings -> Format System (Do not accept yet)
- 3. Accept system format
- 4. After it reboots, go through the setup screen and set everything up
- 5. Once in the home menu, insert the SD card and let it create some files on the card
- 6. Nands are now unlinked, and there are 2 ID folders in your Nintendo 3DS folder on your SD card (one for emunand, another for sysnand)
- IV. rxTools MSET installation
- 1. Copy the rxinstaller.bin from the mset folder into sd:/root
- 3. Go to http://dukesrg.github.io/?rxinstaller.bin
- 4. Once the bottom screen flickers, press Home and you will see an error message (dismiss the error message)
- 5. To access rxTools MSET, Go to System Settings -> Other settings -> Profile -> Nintendo DS Profile
- B. FBI/ROP Injection Method
- 1. Go to http://dukesrg.github.io/?rxTools/sys/code.bin
- 2. Go to Advanced -> Inject FBI -> Emunand -> Check TMD Only
- 4. Copy fbi_inject.app and fbi_inject.tmd from rxTools/tools/fbi_injection/CONSOLE REGION/TMD VERSION/ to sd:/root
- 5. Download latest FBI build https://github.com/Steveice10/FBI
- 7. Go to http://dukesrg.github.io/?rxTools/sys/code.bin
- 8. Go to Advanced -> Inject FBI -> Emunand -> Inject FBI
- 10. Open Health & Safety Information
- 12. Return to Home and open FBI
- 14. Locate rxTools 3.x (console version)
- 15. Press A and restart once installation is finished
- 16. To access rxTools MSET, Go to System Settings -> Other settings -> Profile -> Nintendo DS Profile
- IV. FBI Installation
- 1. Follow steps 1-11 of rxTools MSET installation via FBI/ROP Injection
- 1. Create a blank text file called import.db and title.db in Nintendo 3DS/ID1/ID2/
- 3. Go to System Settings -> Data Management -> Nintendo 3DS -> Software
- 5. Reboot to emunand before proceeding with FBI installation
- V. Emunand
- 2. Update emunand
- Backing up emunand
- http://www.maxconsole.com/maxcon_forums/threads/285550-Backup-Restore-of-Emunand-when-upgrading-replacing-SD-card